DIY: Vintage Wine Box

Here at Bubbles & Boat shoes, we like wine. A lot. Like so much (once it hits your lips..). So it was only natural for us to get into a project that uses a vintage wine box to make a sick-ass storage and/or display piece. There are a couple of options depending on how you want your end product to look and ways of personalizing to make it a great wedding gift.

Here’s how it goes:

1. Get a wine box (duh) – the LCBO has these in the back. You just ask an employee if they have any vintage boxes and they can usually find you one. The other great thing is that it costs you ~$5, and that money is used as a donation to whichever charity the LCBO is supporting at that time (the one pictured went to the SickKids Foundation).  The lid often is broken because of how they have to pry it off – use a strong epoxy or liquid cement to glue the pieces back together.

box1

2. Pull the industrial staples out of the box – I use pliers or wire cutters. Warning – this is actually way harder than it sounds. The wire cutters work well because they get a really firm hold on the staple so that you can pry it up bit by bit. Resist the urge to just cut them or hammer them down (cowards way out), since this won’t look as nice and might shred your hands when you’re sanding.
staple1staple2

3. Fill in the holes in the lid/box left by the staples using a wood filler. Let it dry and fill again until all of the holes have been filled to be flush/slightly higher than the surface of the wood. When the wood filler is 100% dry, sand these down to be totally flush/smooth with the surface of the wood.

filler

4. Once you’ve pulled all of the staples out and your lid is reconstructed, sand all of the edges of the box and the lid. Some boxes will come with slats to hold the wine (even better) – I recommend sanding these as well because then…obviously…you can use your box to hold wine! If you’re going to stain the box, you’ll want to sand the surfaces too so your stain finishes evenly. As you can see, this craft ravages your manicure, so you’ll want to schedule one as a reward for when you’ve finished the project (very important).sand

5. Again, depending on what you want your end product to look like, you can add some decorative aspects to the lid i.e. corner finishes (pictured below), engraving/wood burning etc. Any decorative work on the lid/box should be done before you attach hardware. I used corner finishes on this box, but for a wedding gift, I’ve had the lid laser engraved with the couple’s names/date and a reading from their wedding. If you are going to engrave AND stain it is crucial that you sand the surface very smooth before it’s engraved! (lesson learned the hard way over here).                                    cornercorner2

6. When you’re happy with the state of your box, it’s time for the tricky part – adding hinges. These things are super finicky. A couple of tips for adding these:

– Attach them to the lid first and then use a pillow to support the lid when you’re attaching them to the box.
– Use a tack or a corkscrew (or some other pointy implement…I just happened to have a corkscrew near by) to make a hole. This works to mark where the tiny screws will go and also makes it easier to screw it in.
– When you’re attaching them to the box, do the outside hinges first – this holds the lid in place when you do the remaining screws.
hingehinge3hinge4

7. When you’ve got your hinges on, take a big sip of wine because you’re probably a little frustrated and, hey, you’ve earned it!

8. Then, add your chain (buy it at any Home Hardware etc.) to the inside of the box and underside of the lid to hold the lid when it’s open. You can make it so the lid opens almost all the way to 180° or somewhere closer to 90°. Attaching it to the inside of the box allows the chain to fall inside neatly when you close the lid. I use the extra 4 screws that come with the hinges since they are the right gauge for fitting through the chain and the right length for holding the chain without going all the way through the lid. Obviously, do this to both side of the box.

chain

chain29. Last finishing touch (optional) – add furniture tacks around the edge of the box. This gives it a nice, rustic and professional finish. It also hides the holes where the industrial staples were removed (also a trick to hide any staples left!).

studsstuds2

10. Ta-da! Enjoy your awesome wine box! Or…you know…give it to a friend or something

finished

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s